• 我们以H1信标为例,但此说明适用于H1, H2, H3, 等等
  • 默认密码: Moko4321

使用iBeacon设置信标

在Google Play或Apple应用商店中搜索MokoBeacon. 或点击下面的按钮开始

下载MOKOBeacon APP

1. 开启/关闭H1-iBeacon

开启H1-iBeacon:

按下按钮 (在信标顶盖的中心) 并保持 3 秒;
红色指示灯闪烁几次,然后熄灭, 这意味着信标打开并开始广播.

关闭H1-iBeacon:
按下按钮 (在信标顶盖的中心) 并保持 3 秒;
红色LED灯亮 2 秒然后关闭, 这意味着信标关闭并且停止广播.

2. 扫描并连接到H1-iBeacon

  • 当用户打开手机上的蓝牙时, APP可以搜索附近的H1-iBeacon设备. APP可以通过信号强度对扫描的设备进行分类, 主要或次要价值.
  • 单击需要配置的设备, 将会出现一个对话框,要求您输入密码. 当用户输入正确的密码时, 他可以进入配置界面来配置参数.
  • 如果用户未进行任何操作,设备将自动断开连接 1 分钟. 用户可以点击 断开 on the top right corner of the interface to reconnect App to the device.

3. Configure H1-iBeacon Parameters

Readable and configurable device parameters

  1. - UUID
  2. - Major
  3. - Minor
  4. - Measured Distance(RSSI@1m)
  5. - TX PowerTransmission Power
  6. - Broadcasting Interval
  7. - iBeacon Name
  8. - Device ID
  9. - Password
  10. - Connection Mode

Readable and non-configurable device parameters

  1. - Battery
  2. - MAC Address
  3. - Device Information
  4. - RSSI curve

3.1 Configure UUID

  • Default UUID: E2C56DB5-DFFB-48D2-B060-D0F5A71096E0
  • User can enter the UUID values that meet the requirements of the standard field in the input box(16bytes).

3.2 Configure Major and Minor

  • Default Major: 0
  • Default Minor: 0
  • User writes decimal digits to configure Major and Minor. The value ranges from 0 至 65535, corresponding to hexadecimal 0x0000 to 0xFFFF.

3.3 Configure Measured Distance(RSSI@1m)

  • RSSI—Received Signal Strength Indication
  • RSSI@1m refers to Receiver device receives the signal strength in 1 meter. The value accords with the actual test results. Normally we don’t suggest that user configure this value.

3.4 配置发射功率(发射功率)

  • 设备的传输功率由芯片决定.
  • 默认发射功率: -4分贝.
  • 可以将Tx Power配置为以下数据之一:-40分贝,-30分贝,-20分贝,-16分贝,-12分贝,-8分贝,-4分贝,0分贝,4分贝.

3.5 配置广播间隔

  • 设备广播iBeacon信息的时间间隔.
  • 默认广播间隔: 1000多发性硬化症.
  • 广播间隔的可调间隔为100ms, 和广播间隔从100ms到10s.

3.6 修改设备ID

  • 设备编号,范围从 00000 至 99999.

3.7 iBeacon名称

  • 默认iBeacon名称: “ MkiBeacon_”.
  • iBeacon名称的最大长度为 10 人物 (只有字母, 数字, 并强调).

3.8 修改密码

  • 默认密码: Moko4321
  • 密码长度:8 人物 (仅字母和数字, 并且字母区分大小写).
  • 用户需要两次输入相同的内容来修改密码.

3.9 配置连接模式

  • 默认连接方式: 可连接的.
  • 当H1-iBeacon处于可断开状态时, 设备无法配置. 如果您需要恢复可连接模式, 您应该按照以下步骤操作 (设备处于可断开状态).
  • 1. 长按按钮 3 秒以关闭H1-iBeacon;
  • 2. 长按按钮 3 秒以打开H1-iBeacon;
  • 3. 设备在重启后将处于可连接状态 1 分钟; 用户可以连接到设备并将连接模式更改为可连接状态.

3.10 设备信息

  • 制造商
  • 产品型号
  • 生产日期
  • MAC地址
  • 芯片型号
  • 硬件版本
  • 固件版本
  • 运行时间
  • 系统编号
  • 电气工程师学会
  • 我们以H1信标为例,但此说明适用于H1, H3, 等等
  • 默认密码: Moko4321

使用Eddystone协议设置您的信标

在Google Play或Apple App Store上搜索MokoBeaconX. 或点击下面的按钮开始

下载MokoBeaconX应用

1. 开启/关闭H1-iBeacon

开启H1-iBeacon:

  1. 按下顶盖中央的按钮;
  2. 红色指示灯快速闪烁几次,然后熄灭, 这意味着信标打开并开始广播.

关闭H1-iBeacon:

  1. 按下按钮 (在顶盖的中心) 并继续保持 5 秒;
  2. 红色指示灯闪烁 3 次,然后关闭, 这意味着信标关闭并且停止广播.

2. 扫描并连接到H1-BeaconX

2.1 扫描设备

  1. 打开手机的蓝牙,然后打开APP MokoBeaconX;
  2. 触摸 扫描按钮 在状态栏的左上角启动扫描设备;
  3. 默认扫描时间为 1 分钟;
  4. 用户也可以触摸 扫描按钮 停止扫描;
mokosmart ibeacon eddystone信标设置页面

5. 顶部的“编辑过滤器”可以帮助用户过滤关键字和RSSI. 关键字包括设备名称和Mac地址的一部分; RSSI的范围是-127dBm至0dBm;

例如:
在对话框中输入“ F”,并将RSSI滑至-87dBm, MokoBeaconX将显示RSSI大于-87dBm且设备名称和Mac地址包含“ F”的设备.

2.2 Connect to H1-BeaconX

  1. Touch the blue button “CONNECT” to connect to the device that needs to be configured;
  2. There will be a dialog box asking you to enter the 8 characters password;
  3. 当用户输入正确的密码时, he can enter into the configuration interface to configure H1-BeaconX’s parameters.

3. Configure H1-BeaconX parameters

3.1 SLOTS and Supported frames

有 6 active SLOTs including a default SLOT that broadcasts user-defined data (Device Name/MAC Address/Battery level/Connection status), and the default SLOT cannot be configured as other frame types.

The other 5 active SLOTs can be configured as any of the following types.

Supported frames

  • 涡流石™-UID
  • 涡流石™-网址
  • 涡流石™-TLM
  • 信标 (UUID/Major/Minor)
  • NO DATA(SOLT is shut off)

Users can configure one frame type to different SLOTs. 例如, H1-BeaconX

can broadcast 5 sets of iBeacon data at the same time, or they can simultaneously broadcast 3 sets of URL data plus 1 set of UID data and 1 set of TLM data. Users also can configure the 5 SLOTs as NO DATA,

that means H1-BeaconX only broadcasts user-defined data.

NOTE: TLM shows only one in the broadcast. For more, please click Eddystone-TLM

By default, H1-BeaconX broadcasts URL(https://www.mokosmart.com) and iBeacon. We can adjust the default setting according to the customer’s needs.

3.2 Configure parameters

  • Related data of frame type;
  • Advertising Interval;
  • Tx Power(Transmission Power);
  • Measured Power(RSSI@1m/0m);
  • User-defined data(Device name/Password/Connection status).

Each SLOT has independent TX Power and Measured Power. All SOLTS share a set of Advertising Interval.
After configuring, touch the save button on the upper right corner of the status bar to save settings. Other operations will cancel the configuration.

涡流石™- UID
  1. Namespace--- 10bytes Hexadecimal number
  2. Instance ID --- 6bytes Hexadecimal number
涡流石™- 网址

URL Scheme Prefix

1. http://www.

2. https://www.

3. http://

4. https://

Encoded URL(Any of the following is ok):

1. 1-16 characters and Eddystone-URL HTTP URL encoding(as following);

2. 1-17 人物

Currently supported Eddystone-URL HTTP URL encoding

NOTE: Range 07-13 define the same top level domains as 00-06 without a /.

涡流石™- TLM

NO configurable frame type data.

信标
  1. Major ---0-65535
  2. Minor ---0-65535
  3. UUID---16bytes Hexadecimal number

3.2.2 Advertising Interval

  • Default Advertising Interval: 1000多发性硬化症.
  • The adjustable interval of Advertising Interval is 100ms, and adjustable range of 300ms-4000ms.
  • The Advertising Interval for all SLOTs is the same. It means if you modify Advertising Interval of a SLOT to 500ms, Advertising Interval of other SLOTs will be also modified to 500ms.

3.2.3 Tx Power(Transmission Power)

  • 设备的传输功率由芯片决定.
  • 默认发射功率: 0分贝.
  • 可以将Tx Power配置为以下数据之一:-40分贝,-20分贝,-16分贝,-12分贝,-8分贝,-4分贝,0分贝,4分贝.

3.2.4 Measured Power(RSSI@1m/0m)

  • RSSI—Received Signal Strength Indication.
  • RSSI@1m refers to Receiver device receives the signal strength in 1 meter. (For iBeacon)
  • RSSI@0m refers to Receiver device receives the signal strength in 0 meter. (For Eddystone™ )
  • The value accords with the actual test results. Normally we don’t suggest that users configure this value.

3.2.5 User-defined data

Device Name
  • 默认iBeacon名称: “BeaconX”.
  • The maximum length of H1-BeaconX Device name is 8 人物 (只有字母, 数字, and underlines allowed).
修改密码
  • 默认密码: “Moko4321”.
  • 密码长度:8 人物 (仅字母和数字, 并且字母区分大小写).
  • 用户需要两次输入相同的内容来修改密码.
连接状态
  • 默认连接方式: 可连接的.
  • When H1-BeaconX is in disconnectable status, 设备无法配置. 如果您需要恢复可连接模式, you should follow the below steps (设备处于可断开状态).

1. 长按按钮 5 seconds to turn off H1-BeaconX;

2. Press the button to turn on H1-BeaconX;

3. The device will be in connectable status within 100 times broadcasts; 用户可以连接到设备并将连接模式更改为可连接状态

.

Reset Factory
  • Make the H1-iBeacon to factory settings, but the password will not be restored.
Update Firmware
  • To be developed

4. 设备信息

  • SOC(State of Charge)
  • Mac Address
  • 产品型号
  • Software Version
  • 硬件版本
  • Manufacture Date
  • Manufacture